MicroNet Fibre to SAS/SATA II RAID Subsystem Bedienungsanleitung Seite 102
- Seite / 138
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Fibre to SAS/SATA II RAID Subsystem
102
User Manual
Chapter 6 Maintenance
6.1 Upgrading the RAID Controller’s Cache Memory
The RAID controller is equipped with one DDRII SDRAM socket. By default, the RAID
controller comes with at least 512MB of memory that is expandable to a maximum of 4GB.
The expansion memory module can be purchased from your dealer.
Memory Type: 1.8V PC5300/4200 DDR2 SDRAM 240pin ECC.
Memory Size: Supports 240pin DDR2 of 512MB, 1GB, 2GB, or 4GB.
6.1.1 Replacing the Memory Module
1. Shutdown the RAID controller using the “Shutdown Controller” function in
proRAID Manager GUI.
2. After RAID controller is shutdown, power off the switches of the 2 Power Supply
Fan Modules. Then disconnect the power cables.
3. Disconnect any Fibre cable from the controller module, and then remove the
Controller Module from the slot.
4. Remove the memory module from the RAM socket of the RAID controller by
pressing the ejector clips until the memory module pops out of the socket.
5. Align the new memory module into the socket. Make sure the notch is aligned
with the key on the socket itself. With the ejector clips in open position, press
down the memory module into the socket until it sinks into place. The ejector
clips will automatically close to lock the memory module.
6. Reinsert the Controller Module.
7. If the RAID subsystem has dual (redundant) RAID controllers, repeat Steps 3 to 6
to replace/upgrade the memory of the other Controller Module.
8. Reconnect the Fibre cable(s) to the Controller Module(s). Reconnect the power
cables and power on the 2 switches of the Power Supply Fan Modules.
- Revision 1.2 1
- Table of Contents 2
- Preface 5
- Before You Begin 6
- User Manual 10
- 1.2 RAID Concepts 11
- RAID Management 15
- 1.3 Fibre Functions 16
- 1.4 Array Definition 18
- 1.5 High Availability 19
- 2.1 Main Components 21
- 2.1.1.2 LCD Front Panel 23
- 2.2 Controller Module 27
- 3.1 Powering On 31
- Main Menu 40
- Chapter 5 RAID Management 51
- 5.2 RAID Set Functions 53
- 5.2.2 Delete RAID Set 54
- 5.2.4 Offline RAID Set 58
- 5.2.6 Create Hot Spare 61
- 5.2.7 Delete Hot Spare 62
- 5.2.8 Rescue Raid Set 63
- 5.3 Volume Set Function 64
- 5.3.2 Create Raid 30/50/60 67
- 5.3.3 Delete Volume Set 68
- 5.3.4 Modify Volume Set 69
- 5.3.5 Check Volume Set 72
- 5.3.7 Stop Volume Check 75
- 5.4 Physical Drive 76
- 5.4.4 Identify Enclosure 79
- 5.5 System Controls 81
- 5.5.2 HDD Power Management 83
- 5.5.3 Fibre Channel Config 85
- 5.5.6 SNMP Configuration 89
- 5.5.7 NTP Configuration 90
- 5.5.9 Generate Test Event 92
- 5.5.10 Clear Event Buffer 93
- 5.5.13 Shutdown Controller 95
- 5.5.14 Restart Controller 96
- 5.6 Information Menu 97
- 5.6.3 Hardware Monitor 101
- Chapter 6 Maintenance 102
Philips FC0026836 podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Oświetlenie Philips FC0026836.
Dostarczamy 1 pdf podręczników Philips FC0026836 do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Kommentare zu diesen Handbüchern